The Universal Transmission Test Port Extender allows access to the vehicle’s transmission test port to install a temperature sensor for extremely accurate readings directly from the source. This transmission test port sender extender features a...
The GM Allison 1000 Transmission Line T-Fitting Adapter allows the installation of a 1/8-27 NPT transmission temperature sensor directly onto the 5/8” transmission cooler feed line for extremely accurate readings directly from the source. This GM...
The Dodge Ram Cummins Transmission Line T-Fitting Adapter allows you to easily install your 1/8-27 NPT transmission temperature sensor directly to the 1/2” transmission cooler feed line for extremely accurate readings directly from the source....
MaxTow's Boost T-Fitting Adapter allows you to avoid drilling and tapping into your intake manifold by cutting the MAP line and inserting the T-fitting in the two cut ends. The two included hose clamps allow you to tighten the two ends of MAP line...
MaxTow's 1/8 NPT Drill and Tap Kit is the perfect kit for anyone looking to drill and tap directly into the exhaust manifold or intake manifold. The featured 1/8 NPT Tap is used for tapping thermocouple and boost gauge fitting holes for gauge...
MaxTow's 3/8” Transmission Line T-Fitting Adapter allows you to install your 1/8-27 NPT transmission temperature sensor to the 3/8” transmission cooler feed line for extremely accurate readings directly from the source. This Transmission Line...
MaxTow's 1/8 NPT Fuel Pressure Snubber Valve regulates, normalizes and eliminates fuel pressure spikes present throughout the fuel system during the initial ignition and start up of a diesel engine. The Snubber Valve limits these high-pressure...
MaxTow's 1994-1998 Dodge Ram 12 Valve Cummins Banjo Bolt Adapter replaces the stock banjo bolt and allows access to the injection pump for extremely accurate readings directly from the source. This 12 valve Cummins banjo bolt features a male M14 x...
MaxTow's Banjo Bolt Adapter is specifically designed for the 1994.5-2010 Dodge Ram with a 24 valve Cummins motor. This adapter will replace your stock banjo bolt allowing you to easily install your Snubber Valve and fuel pressure sending unit...
A snubber valve is required when installing a fuel pressure sensor into a Cummins Diesel application. These engines have a fuel pressure spike at startup that can damage the sensor causing premature failure. The snubber valve ensures that the...
In order to accurately determine what size expandable circuit your vehicle uses. You will need to remove a fuse from your fuse panel and compare the sizes. Please refer to this image:
Although The LS Engine Fuel Rail Adapter is not required for installing a fuel pressure gauge on an LS engine it is suggested as it does make the installation easier. This LS Fuel Rail Adapter includes a 1/8" NPT Female to Male 90 Degrees Elbow...
In order to get a fuel pressure reading on a Duramax, you will require an aftermarket lift pump. Some lift pumps have ports on the side that allow sensors to be installed directly into them. However, if your aftermarket lift pump does not offer a...
Although there are additional options for installing a Fuel Pressure Sensor on your 7.3L / 6.0L Powerstroke. We find that the easiest option for installation is with the use of our Powerstroke Fuel Pressure Adapters. These adapters will allow you...
No, The Air Intake Heater Boost Plug Adapter is not required for installation. However, it does help make the install easier as it is designed specifically for the 1999.5-2002 Ford Super Duty 7.3L Power Stroke and 2001-2004 6.6L GM Duramax and...
At this time we offer 4 different Test Port Extenders. Each of them have a ⅛-27 NPT female thread pitch that allows our sensors to be installed into them. However, the male threads on these adapters will vary depending on which one you select. In...
The answer to this question will vary depending on the vehicle you are installing your Fuel Pressure Gauge on and the type of fuel system (factory or aftermarket) being used. The Big Line Kits are only required for 2007.5-2018 Dodge Ram 6.7L...
The Fuel Line Fuel Pressure T-Fitting Adapters allow you to tee off the fuel line for reliable fuel pressure readings directly from the source. This fuel line adapters are the perfect accessory for any vehicle running a 5/16”, ⅜” or 1⁄2” rubber...
No, A Boost Bolt Thread Adapter is not required for the installation of a Boost Gauge. However, it does help make the installation easier as it removes the need to drill and tap your intake when installing a Boost Gauge on a 1998.5-2007.5 Dodge...